• Announcements regarding our community

    2 Topics
    8 Posts

    @skrysl No. Microsoft runs promotions from time to time but the when and what is down to them.

  • Please use this link to gain technical support for any of our products

  • A place to talk about whatever you want

    126 Topics
    319 Posts

    @GunStrauss said in Black Square Analog Baron Fuel Pump Lvars:

    I can upload a profile when I get home in a couple of days, may I ask what controllers you use?

    I'm not sure what you mean by "controller". I think my answer should be "None".
    I have built a cockpit in which I have replicated the pilot's side of the 3D image you see in the Baron in FS2020. So I have physical switches connected to a Leo Bodnar board (BU0836X) and I am using SPAD.neXt to handle the switch inputs for me.

    I have been busy researching and have got it working satisfactorily. I discovered that I have to turn on the correct electrical circuit as well as switch the pump on.

    “A:CIRCUIT SWITCH ON:4, bool”, and “A:CIRCUIT SWITCH ON:5, bool”

    So, for the left pump switch:

    “Set LVAR:VAR_FUEL-SWITCH_PUMP_1 to #"; where # is the state of the switch. 0=Off, 1=Low, 2=High.'

    and Set CIRCUIT_SWITCH_ON:4 to 1 (or 0 for off)

    For the right pump switch:

    Same as above except use “Set LVAR:VAR_FUEL-SWITCH_PUMP_2” and

    for the electrical circuit use “Set CIRCUIT_SWITCH_ON:5 to 1” (or 0 as appropriate)

    Everything is now working as it should.
    Cheers!

  • 5k Topics
    25k Posts

    Sorry this has been so much work for you. I wish I could supply something that worked for every hardware and software combination, but everyone wants something a little different. It's also difficult enough as it is to avoid conflicts with all the popular hardware just as they come out of the box. The Honeycomb products have proven particularly difficult on the developer side.

    I wanted to send this to you days ago, but I couldn't find it again when I went looking. I don't think many people know that this exists and can be helpful for anyone with any software. It's a community driven repository of aircraft controls on Mobiflight's website. I have even less experience with Mobiflight; however, if you can import some of these "presets" or enter code directly, you might find it more useful than SPAD.

    I'm ashamed to say this publicly, lest I draw the ire of those with more complex setups and the developer, but I've been using the same Saitek X52 for 20 years now. I like to keep my things in good condition, so I've never really considered purchasing anything else. I've always been very low maintenance when it comes to such things, I suppose.

  • For all discussion relating to train simulation and Just Trains products

    141 Topics
    314 Posts

    I don't mind the gates too much, since from the cab you see them along then an approximation's OK with me there, considering the engine TS runs on I imagine every saving has to be made in other directions to maximise the quality of the forward view. In the same way my house is at a rather funny angle (although you can't even see it from the railway, so I was pleasantly surprised when it appeared at all on the Hope Valley route).

    I agree Middlewood station looks a bit on the busy side though :)

  • Got a suggestion or some feedback for us? Drop it in here and we'll take a look!

    126 Topics
    285 Posts

    Hi,

    Apart from the ac already in development (F100/A300/747-200), I hope one day we can add the 737-200 to the ever growing list of great classics developed by Justflight.

    Not sure what type of cdu this is in the pic, but it would make a great aircraft to be retrofitted with your upcoming UNS1.
    https://www.airliners.net/photo/Sriwijaya-Air/Boeing-737-284-Adv/1663597/L

    Cheers,

    Luc

  • Looking for an old post? We've kept them on the old forum.